Home > Cannot Stat > Cannot Stat R8169.ko

Cannot Stat R8169.ko

They should just auto mount when you pop them in. Also, there has been a kernel update to 2.6.24-17-generic, and I have included a compiled v6 module for this kernel, as well. YEY I LOVE LINUX hehe! I have installed on Gutsy, a little scared updating up to 8.04 yet.. check over here

v7 might be a different story. V1 VastOne says: July 7, 2008 at 6:04 pm Jameson, I am now online via the wireless side of the RTL8168c in my Ubuntu setup…Can only get an IP via wireless The problem is that the card is still not working. I run this script on Ubuntu X64 kernel 19 and reboot, the net works properly. check over here

Good luck, Jameson Doug says: September 28, 2008 at 4:58 pm Thanks for the encouragement. I believe I cant connect to LAN without installing the NIC card, right? You will have to check hardware manuals or on line to find out if your NICs support Auto-Sense; if not, you'll need a crossover cable or two normal cables and a it saved me hours of pain of trying to figure out how to get this stupid NIC working.

If you still see ubuntu running the r8169 driver then go to your version of: /lib/modules/2.6.27-7-generic/kernel/drivers/net find the r8169.ko file and rename it r8169.ko.old FYI: I'm not a ubuntu expert, but I have attached the "hwinfo -netcard" and "hwinfo --network" for the kind consideration. It worked fine. If for some inconceivable reason you want to use the obsoleted version instead, you can download the old tarball which handles the patching.

I would add for any noobs that look at this in the future that you can add the packages referred to above by typing: “sudo apt-cdrom add” with the installation cd Works a treat. blueskyhff Linux - Networking 2 12-18-2007 01:24 PM Realtek 8168/8111 hang on high load ari197 Linux - Laptop and Netbook 1 12-29-2006 04:42 AM All times are GMT -5. That’s essentially what’s happening tens or hundreds of times when you try to compile a Linux kernel module without the kernel headers.

You must repeat this process each time. Refrigerator says: September 1, 2008 at 11:59 am Well there is a “hardware-driver”-window in the german version which shows the not-proprietary-drivers. Glad to hear your issue was resolved. Jameson says: July 17, 2008 at 9:42 pm Luis, Please post the error message here, along with the output of lsmod | grep r81 and lspci | grep -i eth Jameson

  • Even with new driver NIC failed again today.
  • I’ve also ordered another NIC with a Marvell 88E8001 chipset, if that works then I’ll know it’s the 8111b for sure.
  • Arrikhan Ethan says: January 10, 2009 at 1:07 pm Well done, my friend, well done.
  • Unsafe on 32 bit PCI slot. (int) parm: debug:Debug verbosity level (0=none, …, 16=all) (int) In my last post I was trying to install the v5.16-generic to see if it work
  • Download the latest driver on Realtek's website: http://www.realtek.com.tw/downloads/downloadsView.aspx?Langid=1&PNid=13&PFid=5&Level=5&Conn=4&DownTypeID=3&GetDown=false#2 If you're unsure which kernel you are using, try uname -r After downloading, the README is pretty much telling you anything you need

I have exact the same nic and it just refused to go up every now and then. https://bugs.launchpad.net/bugs/212497 It behaves the same as before with the wrong r8169, no communication with the router. However, I was able to use the manual instructions. Deprecated by ethtool (8). (array of int) parm: speed:force phy operation.

I downloaded the driver from here: http://www.realtek.com.tw/downloads/downloadsView.aspx?Langid=1&PNid=13&PFid=5&Level=5&Conn=4&DownTypeID=3&GetDown=false#2 The driver file: ftp://210.51.181.211/cn/nic/r8168-8.005.00.tar.bz2 It solved my problem for Ubuntu 7.10 but now I have the same problem after upgrading from Ubuntu 7.10 to http://haywirerobotics.com/cannot-stat/cannot-stat-zergrush.html Jameson says: May 20, 2008 at 10:02 pm Hi Kris, Can you show me your output from lspci and lsmod? There was the same error as RafaCortes reported. After removing that (unused) disk, no matter what I do (and I have been trying *a lot of things*) I cannot get any eth0 (or other) device up and running!

Jameson Jameson says: May 27, 2008 at 1:20 am Update: The patched version of the v6 driver source produces a working kernel module. Posted 2 years ago # mojo onlineKey Master /home/slitaz/wok/linux/install No /lib/modules,/lib/firmware,modules.* /boot is empty Posted 2 years ago # alanyih offlineMember http://cook.slitaz.org/undigest/cooker.cgi?pkg=linux USB Empeg empeg-car Mark I/II Driver (USB_SERIAL_EMPEG) [N/m/?] n Jeremy Luke says: September 8, 2008 at 4:07 am Dear Jameson, Thank you very much for your help – I’ll keep looking into it. this content Your script works like a charm!

Using fix IP it shows as it uses it but still no traffic Actualy I do have the r8168 loaded and the r8169 killed as you see in the outputs. Erez K says: September 1, 2008 at 6:52 pm Worked smoothly on my HP m9340f with ubuntu. 8.0.41 desktop for 64bit processors. If you have any more trouble, please post the output of ./switchmods here, and I’ll try to help you along.

You might also have luck with the switchmods script which has just recently been souped up a bit. 😛 jf says: June 2, 2008 at 8:23 am btw , this also

HOSTCC usr/gen_init_cpio UPD include/generated/compile.h LD arch/x86/crypto/built-in.o CC arch/x86/kernel/process_64.o CC kernel/sched.o /usr/src/linux-3.2.53/scripts/gen_initramfs_list.sh: Cannot open 'initrd.cpio' make[1]: *** [usr/initramfs_data.cpio.lzma] Error 1 make: *** [usr] Error 2 2. To use my script, uncompress the tarball, enter the directory, and run the switchmods script: tar xjf r8168_scripts.tar.bz2 cd r8168_scripts sudo ./switchmods; It may be easier to just manually switch in This page no longer deals with the old codebase except for the new note at the end. Both methods are working, and all relevant files can be downloaded at nosemaj.org/dl/r8168_scripts.tar.bz2.

Yes, the output from those commands are pasted below: # make modules make -C src/ modules make[1]: Entering directory `/home/wade/Downloads/NetworkRTL8102E_Driver/r8101-1.010.00/src' make -C /lib/modules/2.6.25.5-1.1-default/build SUBDIRS=/home/wade/Downloads/NetworkRTL8102E_Driver/r8101-1.010.00/src modules make[2]: Entering directory `/usr/src/linux-2.6.25.5-1.1-obj/x86_64/default' make[2]: *** Now it works!!! I had this problem along time, but I didn’t know how to solve. http://haywirerobotics.com/cannot-stat/cp-cannot-stat-no-such-file.html I did not read all the above, I must admit.

Thanks! RTL8111/8168B PCI Express Gigabit Ethernet controller (rev ff) (prog-if ff) !!! rmmod r8169 && modprobe r8169 will show as link NOT detected, after plugging in cable link still isnt detected. So, here’s what you should do: Find out what kernel you’re running: dpkg -l | grep linux-image-2.6.24-19 | awk '{ print $3 }' Download the corresponding Linux headers to a USB

Thanks. Many manny mannyy THANKS. Types of Systems Effected This problem affected (at least) my setup, which was: lspci | grep Ethernet 07:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. sigh.